192.168.1.1

192.168.1.1 Trendchip Router Admin Login Password Change

January 8, 2021 by 192.168.01 Leave a Comment

Trendchip Router Setup: Trendchip Technologies is a classic american networking and technology company which has been producing routers and modems both wired and wireless for a long time now. All their routers are well known for being highly specific for providing better performance in terms of speed and effective usage of bandwidth.

On the other hand, the price for their router models is quite reasonable compared to the routers available in the market. In this article, we are going to discuss the configuration process of Trendchip.

How to Configure Trendchip Router Setup – Trendchip Router Setup Process

Trendchip router models are very great to use because their interface to configure the router is easy to follow and more than that the admin login panel is simplest to follow as well. Follow the below steps to learn the login process first.

Open a browser from your laptop or computer connected to the router and then type the IP address 192.168.1.1
Then you will readily see that the login window will appear on the same window and you will have to enter the login credentials asked
Enter the username and then click on the Next button and then enter the password on the second page and click on the Continue button

After that click on the Continue option present at the bottom of the screen and this will give you access to the admin panel right away.

Trendchip Router Wireless Configuration – Internal Settings

The main thing for any router is that you make sure that the wireless settings are enabled properly and the wireless configuration guide below explains you the same in simple steps.

Wireless Signal Settings: Under Advanced Settings, click on Wireless and select Wireless Signal, on this page make the below said configurations.

Enable 2.4Ghz: Select this option
Wireless Mode: Select “802.11b/g/n mixed” option
Channel: Select “Auto”
Channel Width: Select “20 MHz” option and then click on Apply Changes button to continue

Security Settings: Under Advanced Settings and then click on Wireless through which again click on Security option and then on this page change the settings as per the below instructions.

WiFi Network Name (SSID): Here, you will have to enter a name for your router network
WiFi Network Name (SSID) broadcast: Select “No” option
Security: Select “WPA-PSK/WPA2-PSK” option
WiFi Password ( security key): Here, you have to enter a password for your router network name and you can check the password strength checker to set a strong password and then click on Apply Changes to continue

Guest Network Settings: Sometimes you might have guests at home and you can set this option for such people. Go to the Advanced Settings option from the left sidebar and then under it click on Wireless and finally click on Guest Network option, then on this page make the settings as shown below.

Enable guest network: select this option
WiFi Network Name (SSID): Enter a name for the guest router network
WiFi Network Name (SSID) broadcast: Select “Yes” option
Security: Select “Disabled”
WiFi password ( security key): do not enter any password since this is a guest router network
Then click on Apply Changes option to make the settings

Once you have followed all the above instructions then you can configure the Trendchip router easily in the future as well.

192.168.1.1 Intershop Router Admin Login Password Change

January 8, 2021 by 192.168.01 Leave a Comment

Intershop Router Setup: They are more of a worldwide commerce suite that helps people all across the world to do retail or commerce business. In this aspect, the use of routers is very much valued as an initial product. They used to create routers beforehand but now they have turned thoroughly into commerce as a business and software brand which helps other real businesses to grow with the extent of technology.

But do not think that their routers are still not famous, because these are used by people all across Germany and eastern Europe now as well. In this article, I would be showing you the main aspects that someone who has a new or told Intershop router should be looking directly into.

192.168.1.1 Intershop Admin Login Password Change

How to Configure Intershop Router – Intershop Router Setup Process – 192.168.1.1

IP Address Login: This is the first step, here you have to enter the IP address 192.168.1.1 in the address bar of the router.

After that, a popup for login will appear asking you to enter the username and the password which will be the generic login information.

192.168.1.1 Intershop Router Admin Login

For this, enter the username as “operator” and the password as”$chwarzepumpe” then simply click on the login button to continue.

Internal Configuration and Setup for Intershop Router

Now you will have access to the admin panel directly and simply go over the “WAN” option from the top menu and under this select the “Basic” option and make the changes as below.
- Radio Enable: Select the “Enable” button here
- Network Mode: Select “802.11b/g/n mixed” option from the drop-down menu
- SSID 1: Select “CUSTOMIZED’ then in the second box enter your router network name
- SSID 2: Follow the same pattern as above and only use this if you want to have two router networks
- Country Code: Selec the country from the options
- Channel: Auto
- Channel Width: 20 and then click on Apply button on the top

Advanced Configuration: Then select the “Advanced” option from the same page and follow the settings below.
- BG Protection Mode: Select “Auto” option her
- Beacon Period: Select 100 here and DRM Period should be “1”
- Other options should not be changed and will be automatically populated.
- Then click on the apply button and the settings will be saved.

Go to WPS and then click on the “Enable” option
After that go to the ‘Security” option from the same submenu section under the “Wireless” menu section and then enter the below settings.
- SSID: You have to either select the SSID 1 or SSID 2 which we have setup in the above process.
- Auth Mode: Select “WPAPSK/WPA2PSK mixed mode”
- EncryptType: Select “TKIP” from the drop-down options
- Passphrase: Here enter your password and also make sure that this is at least 8 characters long, then simply click on the Apply button from the above to make the changes.

Finally, we’ve made the wireless connection changes and made the security settings on the Intershop router in about a few minutes which you can do the same by following the above instructions.

192.168.1.1 Lucent Router Admin Login & Password Change

January 8, 2021 by 192.168.01 Leave a Comment

Lucent Router Setup: We have discussed many brands that have been making amazing routers spread all across the world and one such brand is Lucent. Even though Lucent is now closed, it was a very performing multinational telecommunication in the United States of America.

As part of their expansion, they started producing the routers as well which slowly picked up the race and became an essential part of their product lineup over time. Some of the key reasons why their routers were well known are the price was made pretty reasonable and the speed efficiency was great.

Lucent Router Admin Login Password Change

How to setup Lucent Router – Lucent Router Configuration Guide

You have to know that Lucent is a part of the Alcatel router brand so that you will see a lot of crossover products between the two and the same router web configuration panel will also be used since they share the same Internal IP.

Login Step: Even Lucent router has its own internal IP address which is also the same as the Alcatel as they are a part and the IP address is 192.168.1.1.

First, go to any of the browser’s address bar and then enter the IP address 192.168.1.1, then click on the go or the enter button

Wait for the login window to show up and then enter the login information asked which will be username and password.

And both the username and the password is admin, which once entered then you have to click on the login button to load the admin panel.

Lucent Router Wireless Configuration – Internal Settings

Let us now move ahead with the wireless configuration part of the router which is quite simple and can be completed by following the steps shown below.

Wireless Basic Settings: Go to the Wireless, and then from the left sidebar select the “Wireless Basic Settings’’ option and make the below said changes.

Enable Wireless: Check this option

Primary SSID: Here you have to enter the name for the router network and this will be your primary SSID
Secondary SSID: here enter the name for your secondary SSID
Wireless Working Mode: Select “Wireless Access Point(AP)” option
Network Mode: Select “11b/g/n mixed mode” from the drop-down options
SSID Broadcast: Select “Enable” option
AP Isolation: Select “Disable” option
Channel: Select “AutoSelect” option from the drop-down menu
Channel Bandwidth: Select “20/40”
Extension Channel: Select “AutoSelect” option from the drop-down menu
WMM Capable: Select “Enable’ option
APSD Capable: Select “Disable” option

Wireless Security: Go to the Wireless and then select “Wireless Security” option from the left sidebar and then make the changes as per the instructions below.

Select SSID: Select the SSID you have created in the above step from the given drop-down menu options
Security Mode: Select “WPA – PSK(Recommended)” from the drop-down menu
WPA Algorithms: Select “AES(Recommended)” option
Security Key: Enter your router network password and the new password should be at least 8 characters long
WPS Settings: Select “Disable” option and then finally click on the Ok button for the settings to be saved.

192.168.1.1 ACCTON Router Admin Login & Password Change

January 8, 2021 by 192.168.01 Leave a Comment

Accton WiFi Router Admin Login Password Change Setup Guide: Accton which is better known as Accton Technology corporation is a giant Taiwanese company that is in the field of the electronics industry with more than 5200 employees across the world. The primary focus of the brand is to build and create networking and communication service-related tools and most of them are Accton router which is known for its durability and high speed.

Accton Technology has produced a lot of routers out there and among those, I would say MR3200 series is the finest one and has sold more than any other series.

When you buy a new router then it might take some time to understand the configuration and setup process but not anymore. Before we continue to the setup you must connect the ethernet cable from the broadband modem to the Accton router which will enable the Internet power supply.

And then connect the power supply to the router, next connect the ethernet cable from the desktop or laptop to the router ethernet cable port. You can see the Accton Router MR3201A settings and the hardware connection for your reference while making the changes.

How to Install Accton Router – Accton Router Setup Configuration Guide

In this article, we will show you how you can configure the Accton router yourself and make the configuration correct. We will be using the Accton MR3201A router which has been selling well and all other models are almost the same as of this model.

Step 1: Accton Router Default IP Address
- The IP address is the Internet Protocol address or the common IP address which we will use to login to the Accton router admin panel. The default IP address for this router is 192.168.1.1 which you have to enter into the browser’s address bar.

Step 2: Accton Router Default Username and Password
- Once you have entered the IP address in the browser’s address bar you will be asked to login to the admin panel by entering the username and password in the popup that will appear.
- Below are the Accton router’s default username and password which we will have to enter into the sign in popup.

192.168.1.1 Admin Login (User Name & Password)

Step 3: Once we have entered the details, the Accton router admin page will appear through which we have to make the configurations and settings.
Step 4: We have to click on “Networks” under configuration option, then go to “Wi-Fi” option and click on the Enable button

192.168.1.1 Accton WiFi Router Properties

Step 5: Next we will have to select the “Network Security” option from the left sidebar in the configuration section. Here we will have to select the type of encryption, which will be WPS – WPS2.
Step 6: Under the same page we will have to enter the password in the “Password” and make sure that the password should be more than 8 characters long.

Default Username (Admin) and Password for Accton WiFi Router

Brand	Model	Protocol	Username	Password
ACCTON	WIRELESSROUTER Rev. T-ONLINE	HTTP	none	0

Accton Router Default Username and Password

In this way, you will be able to change the Accton Router settings very easily and make sure you have a proper password to protect the router’s Wi-Fi access.

192.168.1.1 Intermec Router Admin Login Password Change

January 7, 2021 by 192.168.01 Leave a Comment

Intermec Router Setup Guide: Intermec is not just known for its range of router that you might be really looking forward to. But this brand is more of a range of data products that are integrated with technology all across the world. Some of their other notable devices or technology products include RFID gadgets, Wireless, and wired communication and networking gadgets which would include the router industry.

At the same time they do not have a large range of routers but a few of them that have performed well over time. In this article, we will glance over the steps required to configure this router brand from scratch.

Intermec Networks Router Admin Login Password Change

How to Configure Intermec Router – Intermec Router Configuration & Setup Guide

Every router brand comes with a different interface and that is why we need to ensure that every user has a basic understanding of how to use their web configuration panel to their fullest.

Step 1: First you have to go to the IP address 192.168.1.1 from your browser’s address bar. In order to do so, simply enter the IP 192.168.1.1 in the address bar

Step 2: Now wait until the login pop will appear and once it does, you have to enter the username which is “admin” and the password is “pass” or “intermec” and then simply press on the login button

Intermec Router Internal Configuration Process

Getting access to the admin panel is an easy task but the configuration is the important one but not hard. And if you follow the instructions below it would become very simple as well.

Step 3: Now, go to the Connection section from the left sidebar and then under it select “Wi-Fi” and then under this page we need to make the below changes.
- Go to the “SSID” under “MAC Filtering Settings” and then here add a name. This will be the name of your router network.
- MAC Filtering Mode: Select “Allow-All” option here
- And finally, click on the “Save Filter Settings” button and the settings will be saved.

Step 4: Then go to the “Gateway” section and then under it select “Wizard” option and here the first step would be to setup a password for your router network.
- Current Password: this will be your present router password
- New Password: you can enter any new password as per your preference
- Re-enter New Password: simply enter the new password again for confirmation
- Then click on the “Next Step” button and then select the “SSID” which we have setup in the above wireless settings.

Step 5: Once the settings are done, I would request you to go to the “Gateway > Hardware” and then to the “Wireless” section again and make sure that both the 2.4 GHz and 5 GHz options are active as shown in the below image. If the status does not show as “Active” then you will have to repeat Step 3 again.

Thanks for reading this article and now we are done with the guide that concludes all the instructions required to configure the Intermec router.

192.168.0.1 or 192.168.1.1 TP-Link Admin Login & Password Change

January 7, 2021 by 192.168.01 Leave a Comment

TP-Link Router Setup: When you talk about World class router service, then the first name that comes to your mind is TP-Link which is a Chinese brand but they are among the top router companies in the world. This company is famous for producing wireless routers, modems, ethernet cables, and many other products for homes and businesses to make the Internet easier to use.

They have a wide range of products as they are focused on creating new products with better features every time and this is one of the reasons why this company has so many reviews and all their products are known for their speed performance moreover.

Find out how to setup & Configure TP-Link Router – Step by step process

So if you own a router from TP-Link then you need to learn how it can be configured, i.e, how someone with no experience can set up the router from scratch. All the routers from TP-Link are very easy to configure and you can follow the instructions below to learn how to configure the router directly.

Step 1: Open your browser and then type in tplinkwifi.net (192.168.0.1 / 192.168.1.1) and then click either the enter button or press on going option to load

Step 2: Then you can see that the login window will appear on the screen now and here you have to enter the username and password as admin & admin respectively and then click on “Let’s Get Started” option to continue

Step 3: In the next page you will be asked to select the Time Zone, select your time zone from the drop down options and then click on the next button

Step 4: On the next page “Internet Connection Type” you will have to click on “Dynamic IP” option and then click on the next button to continue forward in the configuration process

Step 5: Under Quick Step, in the next page you have to select “Do Not Clone MAC Address” option and then click on the Next button to continue

TP-Link Router Quick Setup Clone or do not Clone Mac Address

Step 6: Next Page is Wireless Settings, under this page you have to make the all the below shown settings.

2.4GHz Wireless: Check “Enable Wireless Radio” option
Network Name (SSID): Enter a router network name here as per your preference
Password: Enter a password for your router
5GHZ-1 Wireless: Even here you have to select the option “Enable Wireless Radio” option
Network Name (SSID): Enter a new router network name here
Password: Enter a new router network password here
5Ghz-2 Wireless: Even for this you have to check “Enable Wireless Radio” option
Network Name (SSID): You will have to enter a separate router network name here
Password: Enter a password for this router network here and then click on the next button

Step 7: On the next page of summary you have to review if all the details are correct and then click on the save button

Step 8: Finally you have now configured the router and then you can login or log out from your router and check that wireless setting is enabled for your router.

And in this way you can easily configure any TP-Link router from scratch!