Admin

192.168.1.1 APC Router Admin Login Password Change

November 24, 2020 by 192.168.01 Leave a Comment

APC Router Setup: APC by Schneider Electric is a four-decade long company that has mainly focused on creating power and networking-based products. Out of which the release of APC routers turned out to be great access and the market value for the Internet grew with the advent of new gadgets and modern technology as well. Though they mainly focused on the power of reliable products across their years of making, their products under the router worked great over the seven seasons.

Today we are going to learn more about the configuration process of the APC routers and their related router models through this guide. In case of a new router, you may simply follow the below guide but for an old router, you will have to reset by long pressing on the button on back of the router which will erase the settings and make the router to default settings in no time, once done you can go through the guide below.

APC Router Admin Login and Password Change

How to Configure APC Router – APC Router Setup Guide

I would advise you to make sure that the hardware connection made are rechecked once again and then you can follow the below steps where we will guide through the complete configuration process for the APC router.

First, step here is to enter the APC router default IP address gateway into the address bar of the router. The IP address is 192.168.1.1, which you have to type it into the address bar and then search which will load the login page.
In this step, the login page will appear which will be quite simple to complete, since you have to only enter the username and the password for the APC router and the model you are trying to login for.
Once you have typed in the login details for the router model, click on the login button which will submit the details and sign you in to the admin panel directly!

The primary phase of the guide is completed when you log into the APC router admin panel because from here, we can easily configure the different settings we need.

Go to Wireless section and then select “Wireless Settings” under which you will have to first enable the Wireless WAN connection and this will enable the Wi-Fi to work properly
Then in the same tab, we will have to select the channel frequency to 24MHz and select to the desired number of channels
Then we have to click on the “Wireless Security” option from the left sidebar and under this section, you will change the password setting.
SSID Type: Root
Encryption: WPA (AES)
WPA Authentication Mode: Personal (Pre-Shared Key)
Pre-Shared Key Format: Passphrase
Pre-Shared Key: Enter your password for the router here.
Authentication RADIUS Server: Do not make any changes here

Once the above settings for password and encryption are made, then click on the “Apply Changes” button for the changes to take place.

Since you have completed all the above said steps, we will now have a completely configured APC router with wireless settings enabled and password protection added for security as well.

192.168.0.109 Andover Controls Router Admin Login Password Change

November 24, 2020 by 192.168.01 Leave a Comment

Andover Controls Router Setup: Andover Controls is a pioneer when it comes to the modern router and networking technologies all across the world. This brand pioneered different high performing router that can work with the bandwidth of as high as 500Mbps as well.

The hardware connection for Andover controls is quite simple and follows the same process as any other as well. Here we need to make sure that the broadband ethernet cable is properly connected to the router. Then a power supply is connected to the router always and then an ethernet cable connection is to be established between the router and the working laptop or computer for configuration.

192.168.0.109 Andover Controls Router Admin Login Password Change

How to Configure Andover Controls Router

Andover Controls is a brand that has been for some time right now and their Admin panel configuration actually differs from the modern router we see but we have shown the basic steps that involve the internal configuration of the router below.

One thing you should know is that Andover Controls has released different routers but all these routers comes under the flagship device called Andover Controls Infinity and we are going to discuss that.

The IP address gateway for the router is 192.168.0.109, in order to access the admin panel, you will have to type the given IP gateway into the browser address bar and enter to continue loading the page
The next step is that once the admin panel loads, the page will ask about the login details to be entered which are username as “acc” and password as “acc”. All the routers under this brand or different router models also have the same username and password.
Then, simply click login and you will now be logged into the Andover Controls admin panel through which we can start the settings configuration!
Open the Andover Controls Infinity settings box, through which we will first change the name of the router to the one you would like. Go to the General tab, enter the description with the name RemoteCX and click ok and apply to save the settings

Andover Controls Router General Settings

Then in the same window, select the settings tab where we can now make the Internet settings by changing the IP address.
- You have to make all the IP’s as shown in the image below and Max response time should be 5 seconds
- Then select the “Controller to Cyberstation DB sync” option
- In the homepage section, you can enter any website you want to open when you open a browser from the connected router
- click on and Apply button to save the settings

Andover Controls Router Network Settings

Next, go to the security level and click on the enable option which will make password security available on the router we have setup right now. At the same time in the same tab, go to the password section and enter a password which is at least 8 characters long to ensure the router is password protected.

Finally click on the ok and then the Apply button for the changes made to be saved. We will now have configured the Andover Controls router completely!

192.168.0.109 AOC Router Admin Login & Password Change

November 24, 2020 by 192.168.01 Leave a Comment

AOC Router Setup: AOC is a widespread Router brand across the globe, this is not just used for homes or offices but is used in different transport mediums like Airplanes, Buses, Ships and more for the users to access Wi-Fi with just one click of the button. In the efforts to make the lives of people traveling easier with faster Internet speed and better bandwidth allocation, the brand has strived to manufacture different router that has done over time. In this article, you will learn more about how to get access to the AOC router admin panel and then also learn to configure the internal settings properly.

How to completely Setup AOC Router – AOC Router Internal Configuration Guide

AOC Router IP Gateway: The first step is for you to enter the IP Gateway into the browser from your laptop or computer which will redirect you to their admin panel. We need to use IP 192.168.0.109 as the gateway address.

IP Gateway Login: Once you enter the IP address 192.168.0.109 into the address bar of your browser, a popup will appear asking for the username and password to be entered for the router.

If you click on the go button or press enter then it will lead you directly into the admin panel of the router which we can make the settings from.

Router Internal Configuration – How to enable Wireless, Wi-Fi and Password for the AOC Router

Now we are on the admin panel for the AOC router and the first thing we need to select is to go to the “Operation Mode” and then select the “Wireless ISP” option

Next, step is to go to the “Wireless Settings” section from the left sidebar and then select the “Basic” option under which we will have to make the below following settings.
- Wireless On/Off: Wireless should be on in this option
- Antenna Switch: Internal
- Wireless Mode: You can select from either AP or AP+WDS or WDS as well
- SSID: This will be your router name; you can enter any name which will appear when you search for Wi-Fi and this will appear for your router’s name.
- Broadcast Network Name (SSID): This should be enabled
- AP Isolation: This should be disabled
- MBSSID AP Isolation: This should be disabled
- Frequency (Channel): This should be 2412MHz (Channel 1)

These are the basic settings that are required for you to make the Wireless networking enabled on the router. Once the process and settings are done, click on the Save button which will now enable the Wi-Fi.
Now go to the “Security” option under the “Wireless Settings” section and under this, we will now have to click on enable to make the security enabled. After that select, a password which is 8 characters long or more, enter this in the password section. This will set the password for Wi-Fi access from any of the devices.

In this way, you will be able to configure the AOC router from scratch to the full wireless settings in less than 5 minutes.

192.168.1.1 Belkin Router Admin login Password Change

November 24, 2020 by 192.168.01 Leave a Comment

Belkin Router Admin Login and Password Change with Complete Setup: Every router has got its official page, which is designed to use its features. Belkin Router has its unique interface that lets you change wireless settings, DNS enter, Protect Data connection and so on. To configure the modem as per your requirements you need router default IP address followed by its login credentials.

The default IP address is the same for most models of the router along with Belkin Router models. A proper connection of LAN broadband with router internet port will allow you to access, router interface. We have a detailed guide that will take you stepwise to configure and setup the modem.

192.168.1.1 BELKIN Router Admin Login Password Change

The requirement to set up the router:

There are some basic requirements which are must to be checked before you look at the process to set up the Belkin Router.

Belkin Router Modem
Power supply cable to the modem
Ethernet Connection from Modem to PC or laptop
LAN connection from Broadband to Modem
The browser in PC or Laptop to access router homepage

How to Setup Belkin Router Using Default Username and Password:

I hope that you have checked the list of objects need before we proceed to step the Belkin Router. The IP address for the modem is the same as written in the guide followed by default username and password. The default credentials are always the same as every model of Belkin and if changed you can find manual in the box. A proper set of credentials will only let you access the modem and its homepage.

Make the connection to Modem from LAN broadband to the input slot
Switch on the power supply and connect Ethernet port to PC or Laptops from Modem output
As we have set up the connection, launch the browser and enter the IP address
Default IP address is 192.168.1.1 and then wait for the page to get loaded
Enter Username as Admin and Password as Admin, then click on the login button

That’s it! You have successfully logged into the Belkin Router homepage and you can first attempt to change default credentials. Select the password option to WAP2 to make the wireless connection secure.

How to Setup DNS in Belkin Router:

I hope you have got your DNS open IP address and would like to change the current IP address of automatic. Get followed with below listed steps and you will successfully change DNS entries.

Launch browser in PC or Windows to which router output LAN is connected
Now visits modem IP address by using the IP address 192.168.1.1
Enter the login credentials respective shown on screen and click on the Login button

Clicks on DNS button under Internet WAN option and wait for a while
Enter the password, as modem required to get into DNS settings option
Uncheck Automatic option from ISP and enter DNS address
Enter DNS address as 208.67.222.222 and 208.67.220.220 respective
Click on the Apply changes and Belkin Router DNS settings are configured.

This settings changes of DNS will make sure the router model secure and limited to usage as you configure. The password is must be passed when changing any configuration, else changes settings will be saved and will be cleaned once you log out.

Model Wide Belkin Networks Router Admin Login Default Admin Login & Password Change

Brand	Model	Protocol	Username	Password
BELKIN	F5D6130	SNMP	(none)	MiniAP
BELKIN	F5D7150 Rev. FB	MULTI	n/a	admin
BELKIN	F5D8233-4	HTTP	(blank)	(blank)
BELKIN	F5D7231	HTTP	admin	(blank)

192.168.1.254 2Wire Router Admin Login & Password Change

November 24, 2020 by 192.168.01 Leave a Comment

2Wire Router Setup: 2Wire was a leading Computer and network manufacturing brand in the United States which ran between 1998 to 2010 and was later sold to Pace plc of the United Kingdom. There are a lot of router and computer network solutions across the United States and one of the reasons why 2Wire has become majorly famous is due to widespread home portal and residential router services which were easy to assemble and more convenient as well.

Another big news is that recently ARRIS has acquired the 2Wire brand and has made major changes to turning all the new product gateways to their own cable broadband service or ethernet gateway services.

The 2Wire company has released a lot of Home Portal routers which are now widespread across the United States that are used not just at homes but at different offices as well. There are a lot of 2Wire routers across the globe and today we are going to show you how you can setup a 2Wire router very easily with all the basic instructions required to do so.

2Wire Router Admin Login Password Change

How to Setup 2Wire Router – 2Wire Router Setup Process

Every router that you buy has to be setup before hand you make use of it or else it won’t be useful even after plugging in the ethernet cable. One good thing about 2Wire is that they have a great platform for setting up new routers which one would need at all times. As every brand and router service has its own IP address that is allocated to their routers, even 2Wire has a separate IP address entity which is 192.168.1.254

First, you need to connect 2Wire router to the power source and attach ethernet cable to it, while liking the main way back ethernet cable to your main computer to initially change the router settings such as password and login details for Wi-Fi access.

192.168.1.254 2Wire Router Login — **192.168.1.254** 2Wire Router Login

The first step will be for you to enter 192.168.1.254 IP address in the search bar of the browser once the router is manually setup
Then a popup will appear asking for “Authentication Required” where you have to enter User name and Password for the 2Wire router

Default login details for all 2Wire routers are given below

Brand	Model	Protocol	Username	Password
2WIRE	HOMEPORTAL Rev. SBC YAHOO! DSL	(none)	2Wire	(none)
2WIRE	ALL WIFI ROUTERS	HTTP	(none)	Wireless

192.168.1.254 2Wire Router Login & Password Change

After entering the correct login details, you will now be on the 2Wire router login page where you have to click on the Home button to access the settings page

On the settings page, you have to enable and proceed with the following steps
- Enable Wireless Interface: Click on the checkbox to mark Default: Enabled
- Next under Network Name (SSID) select the type of router which you can select from the dropdown
- Wireless Security: Check this box and setup a password for your Wi-Fi
- Authentication Type: There are 5 settings out of which we suggest you use WPA2-PSK settings from the dropdown

Finally, click on the Save button and now you have successfully completed setting up your new 2Wire router!

192.168.1.1 Arescom Router Admin Login Password Change

November 24, 2020 by 192.168.01 Leave a Comment

Arescom Router Setup: Arescom might not be a name you’ve heard a lot but it is quite a popular computer networking solutions brand that has been serving over years now. Their products are well known for being reasonable but at the same time, the major criteria have been their high performing router that can do well with large bandwidth as well.

In the article today, I will be showing you the complete process through which you can log into the Arescon Internal IP gateway and then make the necessary Internet and Wireless settings for your Wi-Fi to work properly.

Before we deep dive into the process, we need to make sure the simple hardware connection and cable management have been done properly for the Arescom router. You will have to confirm that the Broadband ethernet cable is connected to the router, while a power supply is attached to the router in order to supply power to it.

Arescom Router Admin Login Password Change

The last thing would be to ensure that an ethernet cable is connected from the router to the configuring laptop or computer to make the changes required from settings.

How to Configure Arescom Router – Arescom Router Setup Process

The process to configure the Arescom router is quite simple and the fact that it has a complete setup wizard along with the router makes it easier to setup as well. Follow the below steps carefully since the Arescom router setup follows the old web configuration model.

First, step is to enter the IP address for the router which is 192.168.1.1 or 192.168.1.2 into the address bar and then click enter
Next, you will have to enter the Username and password to login, the login details are displayed at admin panel respectively
In the Admin Panel, you will have to select the settings from the left sidebar and the ones you have to select are
- Ethernet
- Token Ring
- IP
- PPP
- UDP
Once selected, check the “Save” and “All and click on Add button which will save the required settings and make the configuration directly

Then open the NetDSL admin panel, go to the configuration page and from there you have to select the Wireless configuration page and click on Apply button for the Wireless connection to be enabled
Then we have to go to LAN configuration from the same configuration page and click on the Next button will take you to the LAN configuration setup. On this page, you will have to enter the IP address and Subnet mask but these IP details will auto populate. So, simply click on the Apply button and the settings will be saved

Now go to the Password under the security option where we will have to enter the password for the Arescom Network connection. This can be from 8 characters to 63 characters long and once created, click on the Save button.

Finally, we have configured the Arescom router with the complete Internal configuration and settings which has enabled the Wireless connection. Now you can enjoy the seamless Wi-Fi connection with a strong password to access it.

Default Username and Passwords in Model Wide for Arescom Router Admin Login Password Change

Brand	Model	Protocol	Username	Password
ARESCOM	MODEM/ROUTER Rev. 10XX	TELNET	n/a	atc123
ARESCOM	ROUTER Rev. ANY	N/A	(none)	(none)